Bakalářská práce obsahuje charakterizaci experimentálních taveb TRIP ocelí, výpočet teplot fázových přeměn těchto ocelí pomocí software JMatPro na základě chemického složení taveb, zjištění transformačních teplot pomocí kalícího dilatometru Linseis L 78 RITA - QDT a porovnání s výsledky ze software JMatPro. Na kalícím dilatometru byl ověřen vliv vložené deformace vzorků při teplotě austenitizace na hodnoty transformačních teplot TRIP ocelí. Byly porovnány mikrostruktury TRIP ocelí ve výchozím stavu, po tepelném zpracování a tepelném zpracování s vloženou deformací.
Anotace v angličtině
The bachelor's thesis contains the characterization of experimental melts of TRIP steels, the calculation of the phase transformation temperatures of these steels using the JMatPro software based on the chemical composition of the melts, the determination of the transformation temperatures using the Linseis L 78 RITA - QDT hardening dilatometer and comparison with the results from the JMatPro software. The influence of the embedded deformation of the samples at the austenitizing temperature on the values of the transformation temperatures of TRIP steels was verified on the quenching dilatometer. The microstructures of TRIP steels in their initial state, after heat treatment and after heat treatment with embedded deformation were compared.
TRIP steels, dilatometry, hardening dilatometer, high strength steels
Rozsah průvodní práce
54 stran
Jazyk
CZ
Anotace
Bakalářská práce obsahuje charakterizaci experimentálních taveb TRIP ocelí, výpočet teplot fázových přeměn těchto ocelí pomocí software JMatPro na základě chemického složení taveb, zjištění transformačních teplot pomocí kalícího dilatometru Linseis L 78 RITA - QDT a porovnání s výsledky ze software JMatPro. Na kalícím dilatometru byl ověřen vliv vložené deformace vzorků při teplotě austenitizace na hodnoty transformačních teplot TRIP ocelí. Byly porovnány mikrostruktury TRIP ocelí ve výchozím stavu, po tepelném zpracování a tepelném zpracování s vloženou deformací.
Anotace v angličtině
The bachelor's thesis contains the characterization of experimental melts of TRIP steels, the calculation of the phase transformation temperatures of these steels using the JMatPro software based on the chemical composition of the melts, the determination of the transformation temperatures using the Linseis L 78 RITA - QDT hardening dilatometer and comparison with the results from the JMatPro software. The influence of the embedded deformation of the samples at the austenitizing temperature on the values of the transformation temperatures of TRIP steels was verified on the quenching dilatometer. The microstructures of TRIP steels in their initial state, after heat treatment and after heat treatment with embedded deformation were compared.
TRIP steels, dilatometry, hardening dilatometer, high strength steels
Zásady pro vypracování
1. Literární rešerše
a) Dilatometrická termická analýza
b) Vysocepevné oceli
2. Experimentální program
a) Charakterizace výchozího stavu oceli
b) Dilatometrické analýzy
c) Mikrostrukturní analýza
d) Měření tvrdosti
3. Diskuse výsledků
4. Závěr
Zásady pro vypracování
1. Literární rešerše
a) Dilatometrická termická analýza
b) Vysocepevné oceli
2. Experimentální program
a) Charakterizace výchozího stavu oceli
b) Dilatometrické analýzy
c) Mikrostrukturní analýza
d) Měření tvrdosti
3. Diskuse výsledků
4. Závěr
Seznam doporučené literatury
HUNKEL, MARTIN, et al. Chapter 3: Dilatometry, Handbook of Thermal Analysis and Calorimetry, Volume 6, 2018, 103-129.
KHODAIE, NASSEH, et al. Unit cell dilation technique for analyzing dilatometry data in microalloyed steels, Materials Characterization. 2018, 135, 84-95.
BACK, J., G., SURREDDI, K., B. Microstructure analysis of martensitic low alloy carbon steel samples subjected to deformation dilatometry, Materials Characterization, 2019, 157, 109926.
FARAHAT, I., Z., A Dilatometry determination of phase transformation temperatures during heating of Nb bearing low carbon steels. Journal of Materials Processing Technology. 2008, 204 (1-3), 365-369.
Seznam doporučené literatury
HUNKEL, MARTIN, et al. Chapter 3: Dilatometry, Handbook of Thermal Analysis and Calorimetry, Volume 6, 2018, 103-129.
KHODAIE, NASSEH, et al. Unit cell dilation technique for analyzing dilatometry data in microalloyed steels, Materials Characterization. 2018, 135, 84-95.
BACK, J., G., SURREDDI, K., B. Microstructure analysis of martensitic low alloy carbon steel samples subjected to deformation dilatometry, Materials Characterization, 2019, 157, 109926.
FARAHAT, I., Z., A Dilatometry determination of phase transformation temperatures during heating of Nb bearing low carbon steels. Journal of Materials Processing Technology. 2008, 204 (1-3), 365-369.
Přílohy volně vložené
-
Přílohy vázané v práci
-
Převzato z knihovny
Ano
Plný text práce
Hodnocení z obhajoby práce
Velmi dobře
Přílohy
Posudek(y) oponenta
Hodnocení vedoucího
Záznam průběhu obhajoby
Ing. Milan Vnouček, Ph.D.
Proveďte porovnání získaných údajů z JMatPro a dilatometru vzhledem k vstupním parametrům deformace - chemické složení formou tabulky.